ASME B36.10M pdf free download

ASME B36.10M-2015 pdf free download.Welded and Seamless Wrought Steel Pipe.
ASME B36.10M covers the standardization of dimensions of welded and seamless wrought steel pipe for high or low temperatures and pressures.
The word pipe is used, as distinguished from tutie, to apply to tubular products of dimensions commonly used for pipeline and piping systems. Pipe NPS 12 (DN 300) and smaller have outside diameters numerically larger than their corresponding sizes. In contrast, the outside diameters of tubes are numerically identical to the size number for all sizes.
2 SIZE
The size of all pipe is identified by the nominal pipe size.
The manufacture of pipe NPS % (DN 6) to NI’S 12 (DN 300), inclusive, is based on a standardized outside diameter (O.D.). This O.D. was originally selected so that pipe with a standard O.D. and having a wall thickness that was typical of the period would have an inside diameter (I.D.) approximately equal to the nominal size. Although there is no such relation behs’een the existing standard thickness — O.L). and nominal size — these nominal sizes and standard O,D.s continue in use as “standard.”
The manufacture of pipe NI’S 14 (DN 350) and larger proceeds on the basis of an O.D. corresponding to the nominal size.
3 MATERIALS
The dimensional standards for pipe described here are for products covered in ASTM specifications.
4 WALL THICKNESS
The nominal wall thicknesses are given in Table 1.
5 WEIGHTS
The nominal weights of steel pipe are calculated values and are tabulated in Table 1.
The nominal plain end weight, in pounds per foot, is calculated using the following formula:
p outside diameter to the nearest 0.001 in. (the symbol I) is to be used for O.D. only in mathematical equations or formulas)
t p specified wall thickness, rounded to the nearest 0.001 in.
W,.r pnominal plain end mass, rounded to the nearest 0.01 lb/ft
The nominal plain end mass, in kilograms per meter,
is calculated using the following formula:
W, p0O24WI5(D — l)t
where
D p outside diameter to the nearest 0.1 mm for outside diameters that are 16 in. (406.4 mm) and smaller and to the nearest 1.0 mm for outside diameters larger than 16 in. (406.4 mm) (the symbol D is to be used for O.D. only in mathematical equations or formulas)
p specified wall thickness, rounded to the nearest 0.01 mm
W. pnominal plain end mass, rounded to the nearest 0.01 kg/rn
6 PERMISSIBLE VARIATIONS
Variations in dimensions differ depending upon the method of manufacture employed in making the pipe to the various specifications available. Permissible ‘ariations for dimensions are indicated in each specification.
7 PIPE THREADS
Unless otherwise specified, the threads of threaded pipe shall conform to ANSI / ASME B1.20.1, Pipe Threads, General Purpose (Inch).
Schedules 5 and 10 wall thicknesses do not permit threading in accordance with ANSI/ASME B1.20.1.
8 WALL THICKNESS DESIGNATIONS
The wall thickness designations Standard, Extra- Strong, and Double Extra-Strong have been commercially used designations for many years. As explained in the Foreword, the Schedule Numbers were subsequently added as a convenient designation for use in ordering pipe. Standard and Schedule 40 are identical for up to NPS 10 (DN 250), inclusive. AIll larger sizes of Standard have / in. (9.53 mm) wall thicknesses.
Extra-Strong and Schedule 80 are identical for up to NPS 8 (DN 200)， inclusive. All larger sizes of Extra Strong have 2 in. (12.70 mm) wall thicknesses. Pipe of sizes and wall thicknesses other than those of Standard, Extra Strong, and Double Extra Strong, and Schedule Number were adopted from API Specification 5L. It was not considered practical to establish Schedule Numbers or new designations for them.ASME B36.10M pdf download.