ASME A112.6.7 pdf free download
ASME A112.6.7-2010 pdf free download.Sanitary Floor Sinks.
1.2 Units of Measurement
Values are stated in U.S. Customary units and the International System of Units (SI). The US. Customary units shall be considered as the standard.
1.3 References
The following documents form a part of this Standard to the extent specified herein. Unless otherwise specified, the latest edition shall apply.
ASME A112.6.3-2001, Floor and Trench Drains ASME Al 12.18.1 /CSA 13125.1-05, Plumbing Fixture Fittings
ASME A112.18.2/CSA B 125.2-05, Plumbing Fixture Waste Fittings
ASME A112.19.1/CSA 1345.2-08, Enameled Cast Iron and Enameled Steel Plumbing Fixtures
ASM E Al 12. 19.3/CSA 1345,4-08, Stainless Steel Plumbing Fixtures
Publisher: The American Society of Mechanical
Engineers (ASME). Three Park Avenue, New York,
NY 10016.5990; Order Department: 22 Law Drive,
P.O. Box 2900, Fairfield, NJ 07007-2900
(www.asme.org)
ASTM A 888, Standard Specification for Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping Applications
ASTM D 522, Standard Test Methods for Mandrel Bend Test of Attached Organic Coatings
ASTM D 523, Standard Test Method for Specular Gloss ASTM D 1784, Standard Specification for Rigid Pol (Vinyl Chloride) (l’VC) Compounds and Chlorinated Poly (Vinyl Chloride) (CPVC) Compounds
ASTM D 2665. Standard Specification for Poly (Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings
American Society for Testing and Materials (ASTM International), 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428.2959 (www.astm.org)
1.4 FLoor Sink
As covered in this Standard, a floor sink is a receptor drain that is designed and installed for the purpose of draining indirect waste to the sanitary drainage system.
2 GENERAL REQUIREMENTS
2.1 Materials
2.1.1 Enameled and Epoxy-Coated Cast Iron Floor Sink. The enameled and epoxy-coated cast iron floor sink shall conform to the general requirements outlined in ASME Al 12.19.1 /CSA B45.2-08, Section 4, and surface shall be examined for blemishes in accordance with para. 5.2.
2.1.2 PVC Plastic Floor Sinks. PVC floor sinks shall be made of a single PVC *. irgin compound except as provided in para. 2.1.2.1, and shall conform to the requirements specified in ASTM D 1784 For a PVC 12454 compound, The PVC plastic floor sinks shall conform to the general requirements outlined in IAPMO/ ANSI Z124.6-2007, Section 2 and workmanship and finish in Section 3.
2.1.2.1 Reworked Plastic. Clean, reworked plastic generated from the manufacturer’s own PVC 12454 products may be used provided the Floor sinks produced meet the requirements of this Standard.
2.1.3 Stainless Steel Floor Sinks. The stainless floor sink shall conform to the general requirements outlined in ASME Al 12.19.3/CSA 845.4-08, Section 4, and surface shall be examined for blemishes in accordance with para. 5.1.
2.2 Epoxy Coating
The visible surface after installation of each floor sink shall be acid-resisting epoxy, thoroughly fused to the cast iron base. It shall be free from Flaws that may affect the appearance or serviceability of the floor sink. The epoxy surface shall meet the requirements of ASME A112.19.I/CSA B45.2-08, para. 4.12 when evaluated for surface defects in accordance with para. 5.2.ASME A112.6.7 pdf download.
