ASME PTB-9 pdf free download

ASME PTB-9-2014 pdf free download.ASME Pipeline Standards Compendium.
2.1 Design of Pipeline Components
2.1.1 CFR Reference: 192.147 Flanges and Flange Accessories
2.1.1.1 CFR I anguage: 192.147(a)
Each flange or flange accessory (other than cast iron) must meet the minimum requirements of ASME/ANSI B 16.5, MSS SP-44. or the equivalent.
2.1.1.2 ASMI Standard Reference
The (‘FR references ASME B 16.5 “Pipe Flanges and Flanged Fittings: NPS ‘/z through NPS 24 Metric/Inch Standard”, in its entirety.
2.1.1.3 CFR language: 192.147(c)
Each flange on a flanged joint in cast iron pipe must conform in dimensions, drilling, face and gasket design to ASMEANSI Bl6.1 and be cast integrally with the pipe, valve, or fitting.
2.1.1.4 ASMF Standard Reference
The CFR references ASME 1116.1 “Gray Iron Pipe Flanges and Flanged Fittings: (Classes 25, 125, and 250)” in its entirety.
2.1.2 CFR Reference: 192.153 Components Fabricated by Welding
2.1.2.1 CFR Language: 192.153(a)
(a) Except For branch connections and assemblies of standard pipe and fittings joined by circumferential welds, the design pressure of each component fabricated by welding. whose strength cannot be determined, must be established in accordance with paragraph UG- 101 of Section VIII. Division 1. of the ASMI- Boiler and Pressure Vessel Code.
2.1.2.2 ASMI Standard Reference
The CFR retrences ASMF. Boiler & Pressure Vessel Code, Section VIII, Division I, “Rules for Construction of Pressure Vessels”, paragraph UG-lOl.
2.1.2.3 CFR Language: 192.153(b)
(b) Each prefabricated unit that uses plate and longitudinal seams must be designed, constructed, and tested in accordance with Section I. Section VIII. Division I, or Section VIII. Division 2 of the ASME Boiler and Pressure Vessel Code, except for the following:
(I) Regularly manufactured buttwelding fittings.
‘2) Pipe that has been produced and tested under a specification listed in appendix B to this part.
(3) Partial assemblies such as split rings or collars.
(4) Prefabricated units that the manufacturer certifies have been tested to at least twice the maximum pressure to which they will be subjected under the anticipated operating conditions.
PTB-9-2014: ASME Pipeline Standards Compendium
2.1.2.4 ASMF Standard Reference
The CFR references ASMIE Boiler & Pressure Vessel Code. Section VIII. Division I, “Rules for
Construction of Pressure Vessels” in its entirety and ASME Boiler & Pressure Vessel Code, Section VIII.
Division 2. “Alternative Rules. Rules for Construction of Pressure Vessels” in its entirety.
2.1.2.5 CFR Language: 192.153(d)
f’d Except for flat elosures designed in accordance with Section VIII of the ASME Boiler and Pressure Code, flat closures and fish tails may not be used on pipe that either operates at 100 psi (689 kPa) gage, or more, or is more than 3 inches (76 millimeters) nominal diameter.
2.1.2.6 ASMF Standard Reference
The CFR retrences ASMIE Boiler & Pressure Vessel Code, Section ‘lIl Division I, Rules for
Construction of Pressure Vessels” in its entirety and ASME Boiler & Pressure Vessel Code. Section VIII.
Division 2, “Alternative Rules. Rules for Construction of Pressure Vessels” in its entirety.
2.1.3 CFR Reference: 192.165 Compressor Stations: Liquid Removal
2.1.3.1 CFR Language: 192.165(b)(3)
th) Each liquid separator used to remove entrained liquids at a compressor station must:
(3) Be manufactured in accordance with Section VIII of the ASME Boiler and Pressure Vessel Code, except that liquid separators constructed of pipe and fittings without internal welding must he fabricated with a design factor of 0.4, or less.
2.1.3.2 ASME Standard Reference
The CFR references ASME Boiler & Pressure Vessel Code, Section VIII, Division I, “Rules for (‘onstruction of Pressure Vessels” in its entirety and ASME Boiler & Pressure Vessel Code, Section VIII, Division 2, “Alternative Rules, Rules for Construction of Pressure Vessels” in its entirety.ASME PTB-9 pdf download.